Published July 6, 2026 at 13:39
Moisture diagnostics in buildings — whether for insurance investigations, renovation assessments, or routine property management inspections — rely on first locating the damp area and then verifying the moisture content. A traditional workflow uses two separate instruments: a thermal imaging camera to locate ”cold spots” on the surface (indicating moisture or missing insulation) and a pin-type moisture meter to confirm moisture levels at that specific point. The FLIR MR160 combines both into a single instrument — providing a significantly more efficient workflow and fewer steps between detection and verification.
What the FLIR MR160 Is
The FLIR Moisture Meter with Built-in Thermal Imager (MR160) is a combination instrument that integrates:
- A thermal camera for visual detection of moisture areas.
- An internal pinless (capacitive) moisture sensor for fast, non-destructive measurements.
- An external pin probe for measuring moisture content in porous materials (wood, drywall).
- Image storage for documentation.
- A rechargeable internal battery.
Key advantage: the thermal camera and moisture meter communicate in real time — when you point the camera at a suspect area, the moisture reading is displayed directly alongside the thermal image on the screen, without needing to switch between different instruments.
Basic specifications:
- Thermal imager: FLIR Lepton microbolometer
- Thermal resolution: 80×60 pixels (4,800 thermal measurement points)
- Thermal measurement range: -10 °C to +150 °C
- Thermal accuracy: ±2 °C or ±2% (whichever is greater)
- Moisture measurement (pinless): Capacitive, up to ~2 cm depth
- Moisture measurement (pin probe): External cable, for wood/drywall penetration measurements
- Moisture content range: 0-100% relative scale
- Battery: Rechargeable Li-Ion, ~8 hours of use
- Ingress protection: IP54
- Weight: ~360 g including battery
- Image storage: MicroSD, JPEG
Why Pin Probes Alone Are Not Enough for Building Diagnostics
Traditional pin moisture measurement has three practical limitations:
Spot-specific nature of the measurement: The pins measure the moisture content precisely at the pin contact point. If the damage is 30 cm to the side, the reading is meaningless. The operator has to ”guess” where to insert the pins — which is the exact problem in the first place.
Shallow measurement depth: The pins typically penetrate 25-40 mm into the material. Water located deeper (behind drywall, inside insulation, within floor structures) will not register in the pin measurement at all.
Material-dependent calibration: Moisture content calculations are calibrated for wood. On drywall, concrete, or insulation materials, the pin reading provides an indication rather than a calibrated value. The operator must understand that ”20%” in a wood material does not mean the same thing as ”20%” on drywall.
What the Thermal Camera Adds
A thermal image of a wall with concealed moisture displays a distinct cold-spot pattern:
- Water has a higher heat capacity than dry building materials.
- Water conducts heat better than air.
- Evaporation from a wet surface cools the surface down.
The net effect: damp areas are typically 1-4 °C colder than surrounding dry areas on the same wall. This is well within the thermal camera’s sensitivity to display as a clear cold spot.
The workflow becomes:
- Scan the entire wall with the thermal camera.
- Identify thermal anomalies (cold spots).
- Aim the pin probe at the center of the cold spot.
- Verify moisture content at the location showing the strongest thermal anomaly.
- Save the thermal image + moisture reading for documentation.
Practical Limitations of Thermal Imaging
Thermal diagnostics are highly effective but not infallible:
- External temperature differences are required: If the indoor and outdoor surfaces of a wall have the same temperature (new construction, overcast mild days), the thermal contrast will be minimal. Best results are achieved during winter conditions (cold outdoors, warm indoors) or after heating up the area.
- Air movement: Drafts from AC ducts or vents create cold spots that have nothing to do with moisture. The operator must interpret thermal images with knowledge of the building’s layout and construction.
- Surface finish and materials: Certain materials (metals, mirrored surfaces) reflect thermal radiation and yield misleading images. Tiled surfaces can also be difficult to interpret thermally.
- Depth limitations: A thermal camera only sees surface temperature contrast. Moisture located deep behind several layers of insulation cannot be detected.
Where the Combination Instrument Makes a Real Difference
Insurance investigations after water damage: Documenting the extent of damage is essential for claim approvals. Combining thermal images with moisture readings is standard practice for insurance adjusters.
Property management: Routine inspections of apartments to detect leaks early (from bathrooms, kitchens, roofs).
Demolition and restoration planning: Prior to demolition, assessing which materials are moisture-damaged and must be removed.
Insulation verification: Checking newly installed insulation — thermal images show whether insulation is installed properly or if thermal bridges are present.
Mold remediation: Before remediation begins, the scope of work must be determined. After remediation, verification is required to confirm that the moisture source has been eliminated.
Roof leak detection: Water penetrating through a roof spreads across truss and framing structures. Thermal imaging from the interior ceiling shows where the water has traveled, even if the actual drip point is elsewhere.
Underfloor heating diagnostics: Cold spots in an underfloor heating loop indicate either air locks or leaks. A thermal image pinpoints the exact loop affected.
In-wall pipe leaks: Water pipes leaking inside walls often start small and can drip for months before visible damage occurs. Thermal imaging can reveal the moisture dispersion pattern early.
Post-construction moisture monitoring: New builds must dry out properly before final finishes are installed. Thermal images + moisture readings document drying progress effectively.
What You Get for Your Money
FLIR MR160 moisture meter with built-in thermal imager, FLIR Lepton thermal sensor 80×60 pixels, thermal measurement range -10 to +150 °C, ±2 °C accuracy, integrated pinless capacitive moisture sensor (up to ~2 cm depth), external pin probe for moisture content in wood and porous materials, MicroSD image storage, rechargeable Li-Ion battery, IP54 protection rating, ~360 g.
7,675 SEK is the instrument investment. Compared to a separate FLIR TG167 spot thermal camera (5,800 SEK) plus a separate pin-type moisture meter (2,000-4,000 SEK), the MR160 delivers the same functionality in a single device, with the crucial advantage that the thermal image and moisture reading are displayed simultaneously on the same screen. This eliminates switching back and forth between two instruments and the risk of confusing which reading belongs to which spot.
Read more: FLIR MR160 moisture meter with thermal camera in the shop →