Published July 11, 2026 at 02:54
A commercial property owner reports that the kitchen exhaust fan on the third floor trips intermittently. Sven, the electrician, arrives on site and stands in front of the electrical room housing the power feed to the fan. Without a thermal imaging camera, he would need to:
- Shut off power to the electrical panel (requiring de-energizing other equipment on the same section).
- Remove the panel’s front cover.
- Verify with a voltmeter that it is de-energized.
- Manually inspect every fuse, every terminal, every cable.
- Turn the power back on and perform tests with a DMM to locate the problem.
Total time: 30–60 minutes. Risk level: high (fumbling inside an energized panel if safety procedures are compromised).
With the FLIR DM166, Sven instead positions the multimeter-thermal imager 50 cm from the FRONT of the electrical panel, checks the screen, and sees in the thermal image that a single fuse is 40 °C hotter than the others. He now knows instantly WHERE the problem is and can plan his method of work from there. Total analysis time: 2 minutes. This is the innovation behind ”Infrared Guided Measurement” (IGM) — the dedicated FLIR technology that combines a thermal imaging camera with a multimeter.
The IGM Technology: The Thermal Imager as the Guide, the DMM as the Verifier
IGM (Infrared Guided Measurement) is FLIR’s proprietary trademark for the concept of INTEGRATING a thermal camera into a work tool where the camera is NOT the instrument’s primary function, but rather a GUIDE to the instrument’s main measurement.
The concept:
- The DM166 multimeter is fundamentally a full-featured TRMS multimeter — AC/DC voltage, current, frequency, resistance, capacitance, continuity, diodes.
- The multimeter also features a built-in FLIR Lepton thermal imaging module with an 80×60 pixel microbolometer array.
- Before test leads are connected to any point, the operator uses the thermal imaging function to SEE where the heat is. This is the infrared guided part.
- Once the point is identified, test leads are connected there for electrical verification.
This workflow is fundamentally different from the traditional ”connect probes everywhere until you find the fault” approach.
Why Overheating Is Almost Always the Symptom
Electrical faults most often manifest as EXCESSIVE HEAT GENERATION. The physics behind this is simple:
P = I² × R
Power dissipation (P, watts) in an electrical component is proportional to the current squared and the resistance. If something goes wrong:
- Loose connection: contact resistance increases. At the same current, P increases. A 10 A connection that is normally 0.01 Ω (P = 1 W) becomes 0.1 Ω when oxidized (P = 10 W). The temperature rises 40–100 °C above ambient.
- Overloaded circuit: the current is too high. At 15 A in a 10 A circuit, P increases by (15/10)² = 2.25× — components run hotter.
- Short circuit: resistance approaches zero, current spikes dramatically. Thermal runaway occurs.
- Degraded capacitor: equivalent series resistance (ESR) increases. The capacitor starts heating up during operation.
- Drifted resistor: resistance value drifts. Power dissipation changes. Temperature changes.
In virtually all fault scenarios, an anomaly shows up as a temperature abnormality before it appears as anything else. This is why a thermal imaging camera is such a powerful diagnostic tool for electrical work.
What the 80×60 Lepton Sensor Shows
The DM166’s built-in Lepton micro-thermography sensor features an 80×60 pixel resolution. This is LESS than a standalone thermal camera (FLIR E5 has 160×120, professional models like the E85 have 320×240), but substantially MORE than an IR spot thermometer (which effectively has 1 pixel).
Practical result: you see a compact thermal image display (typically shown in false color on the multimeter’s 200×150-pixel LCD screen). The image provides enough detail to distinguish INDIVIDUAL components — individual fuses, individual connections, individual cables. However, it is NOT intended for microscopic analysis.
Range and accuracy:
- Temperature range: -10 to +150 °C typical.
- Accuracy: ±3 °C or ±3% of reading.
- Refresh rate: 9 Hz.
- Thermal sensitivity (NETD): ~150 mK — capable of detecting 0.15 °C differences.
The 9 Hz refresh rate is a result of export control regulations. Frame rates below 9 Hz are classified as ”commercial” and do not require export licensing; rates above 9 Hz are classified as military equipment in certain jurisdictions. FLIR deliberately designs its commercial instruments to stay below this threshold.
Multimeter Functions in the DM166
While the thermal camera represents the unique value proposition, the multimeter functionality itself is exceptionally capable:
- DC voltage: up to 1,000 V, ±0.5% accuracy.
- AC voltage (TRMS): up to 750 V, ±1.0%. TRMS stands for ”True Root-Mean-Square” — measuring accurately even on non-sinusoidal waveforms (common in modern electrical systems with switched-mode power supplies).
- DC current: up to 10 A direct, higher with clamp.
- AC current (TRMS): up to 10 A direct.
- Resistance: 0.1 Ω to 40 MΩ.
- Capacitance: 4 nF to 200 μF. Critical for verifying capacitors in motor start circuits.
- Frequency: 0.001 Hz to 1 MHz. Verification of AC line frequency (50 Hz in Sweden, can drift under major grid disturbances).
- Continuity: with audible beeper for fast verification.
- Diode test: for verifying rectifier bridges.
Safety rating: The DM166 is rated CAT III 600V and CAT IV 300V — meaning it is safe for use in typical distribution panels and sub-panels.
Standard Workflow: 3-Step Diagnostics with the DM166
Step 1 — SCANNING: Switch on thermal imaging mode. Aim the multimeter at the electrical equipment from a distance of 30–100 cm. Watch the LCD screen. Look for:
- Individual hot spots that are 10+ °C above ambient.
- Breaks in symmetry: three fuses seated side by side — if one is hot and two are cool, the hot one is the point of interest.
- Thermal gradients: a cable that is warmer at one end than the other indicates poor contact resistance at the warmer terminal.
Step 2 — PINPOINTING: Use the MAX temperature measurement feature on the thermal imager to accurately pinpoint the hottest point. Note the location.
Step 3 — VERIFICATION: After following standard safety procedures (if required), connect the DMM leads to the identified point. Perform a voltage, continuity, or resistance measurement to verify the fault hypothesis.
Using this 3-step method, 80% of electrical faults are located without opening electrical panels or enclosures.
Applications
Commercial electrical service: Properties, offices, restaurants, retail stores. Regular thermal inspections are low-cost insurance against fire hazards.
Industrial maintenance: Motor circuits, compressors, HVAC controls. Thermal hot spots reveal developing wear weeks or months before catastrophic failure.
Electronics repair: PCB-level troubleshooting. Individual overheating ICs become visible on the thermal camera at startup.
Solar panel maintenance: Panel hot spots indicate defective cells. Ground-level module inspections.
HVAC technicians working with electrical components: Heat pumps, water heaters with electric heating elements. Combined thermal and electrical diagnostics.
Automation integrators: PLC systems, DC drives, servo motor controllers. Troubleshooting intermittent faults.
Automotive electricians: Vehicle electronics, battery terminals, alternator circuits. Fast diagnostics without disconnecting harnesses.
Data center technicians: Server rooms, power distribution panels, UPS units. Hot spot detection as part of standard maintenance routines.
What the DM166 Does NOT Replace
- A dedicated thermal imaging camera for building thermography: 80×60 pixels is not sufficient for surveying entire building facades.
- An oscilloscope for signal analysis: The DM166 measures DC, RMS AC, and frequency — but does not capture waveforms.
- An insulation tester (megohmmeter): The DM166’s resistance range reaches up to 40 MΩ; insulation testing requires 500–1000 V test voltages up to 200 GΩ.
- A clamp meter for high currents: The DM166 directly measures up to 10 A. For 100+ A, a current clamp accessory is required.
- An RCD/GFCI tester: Measuring residual fault currents requires dedicated instruments (RCD testers).
What You Get for the Money
FLIR DM166 True-RMS multimeter with built-in Lepton 80×60 thermal camera, IGM (Infrared Guided Measurement) technology, temperature range -10 to +150 °C, ±3 °C thermal imaging accuracy, DC voltage up to 1,000 V and AC (TRMS) up to 750 V, DC/AC current up to 10 A, resistance 0.1 Ω–40 MΩ, capacitance 4 nF–200 μF, frequency 0.001 Hz–1 MHz, continuity with beeper, diode test, CAT III 600 V / CAT IV 300 V rated, LCD display with thermal image view, battery powered, rugged ergonomic design. 6,051 SEK.
The go-to instrument for commercial electricians, industrial maintenance technicians, electronics repair, and other applications where rapid thermal pinpointing of electrical faults is critical. The 3,000–4,000 SEK price premium over standard TRMS multimeters is readily justified by dramatically faster troubleshooting speeds and the increased safety of non-contact inspection before opening energized equipment.
Read more: FLIR DM166 TRMS multimeter with IGM thermal camera in the store →