Hoppa till innehåll
Free shipping over SEK 3,000 excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The camera pinpoints the suspect, the measurement probes confirm the faultThe display shows three values simultaneously – exactly as many as you needDon’t look for a value, look for what deviates from its neighborsThe laser dot is not what you measure, it only indicates the center of the measurement spotA calibration certificate doesn’t prove the measurement is correct, only that the instrument isn’t wrongMultimeter with thermal imaging camera — the most important measurement is the one you make before opening the cabinetIR Thermometer with Thermocouple Input — Infrared Always Measures a Surface, Never What Lies Beneath ItAdjustable Emissivity 0.10–1.00 — Why Your IR Thermometer Gives Inaccurate Readings on Shiny MetalIR thermometer with 50:1 optics — at a distance of two meters, an 8:1 thermometer measures an area the size of a dinner plateExtech IR267 mini IR thermometer 12:1 with type K input up to 600 °C: When 903 kr is enough for surface temperature, core temperature AND air temperature in ONE compact bodyVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The camera pinpoints the suspect, the measurement probes confirm the faultThe display shows three values simultaneously – exactly as many as you needDon’t look for a value, look for what deviates from its neighborsThe laser dot is not what you measure, it only indicates the center of the measurement spotA calibration certificate doesn’t prove the measurement is correct, only that the instrument isn’t wrongMultimeter with thermal imaging camera — the most important measurement is the one you make before opening the cabinetIR Thermometer with Thermocouple Input — Infrared Always Measures a Surface, Never What Lies Beneath ItAdjustable Emissivity 0.10–1.00 — Why Your IR Thermometer Gives Inaccurate Readings on Shiny MetalIR thermometer with 50:1 optics — at a distance of two meters, an 8:1 thermometer measures an area the size of a dinner plateExtech IR267 mini IR thermometer 12:1 with type K input up to 600 °C: When 903 kr is enough for surface temperature, core temperature AND air temperature in ONE compact body

FLIR CM275 AC/DC Clamp Meter + IGM Thermal Imaging Camera + NIST Cert: When a 63 A load on a 10 A fuse shows up as an 87 °C localized hot spot BEFORE the fuse blows

Published July 14, 2026 at 07:09

Electrical maintenance technicians have traditionally carried two separate tools for electrical cabinet diagnostics:

  1. A clamp meter to measure the current flowing through conductors without breaking the circuit (the clamp encloses the cable, measures the magnetic field, and converts it into a current reading).
  2. An IR thermometer or thermal imaging camera to locate ”hot spots” — components running too hot due to overloading, poor connections, or internal defects.

The two tools are used sequentially: the thermal imaging camera first locates the hot area, and the clamp meter is then used to measure the current in the suspected conductor. The FLIR CM275 merges both into a single instrument, eliminating tool-switching time and enabling simultaneous readings of both parameters.

IGM (Infrared Guided Measurement) — What It Means

IGM is FLIR’s trademarked term for ”IR-visually guided measurement” — the concept that a thermal imaging camera should NOT replace traditional measurements, but rather GUIDE the operator to the correct measurement point.

Practical workflow:

  1. Open the electrical cabinet.
  2. Turn on the CM275, activate IGM mode (the thermal image appears on the display).
  3. Pan the thermal camera across the components in the cabinet.
  4. The color overlay displays hot areas in red/yellow and cold areas in blue/green.
  5. Identify the HOTTEST area (which is likely the source of the problem).
  6. Clamp the meter onto the relevant conductor.
  7. Read the current at the same time the thermal camera displays the temperature on the conductor.

Advantages over the traditional ”check each component one by one” approach:

  • No physical contact with potentially energized parts (safety advantage).
  • Rapid problem identification — heat is the most reliable early warning signal.
  • Documentation as an image file containing both the IR image and electrical values.

Thermal Camera Specifications

The CM275’s built-in thermal camera features:

  • Resolution: 80 × 60 pixels (4,800 thermal measurement points).
  • Temperature range: -10 to +150 °C (adjustable).
  • Thermal sensitivity: ~150 mK (capable of distinguishing 0.15 °C differences).
  • Frame rate: 8.7 Hz — sufficient for real-time scanning.
  • Center-point measurement: precise temperature reading for the pixel in the center of the image.

The 80×60 resolution is not studio quality (professional thermographers use 320×240 or 640×480), but it is fully sufficient for electrical diagnostics where you are looking for distinct hot spots rather than subtle temperature gradients.

Clamp Meter Specifications

  • AC current: 0–600 A True-RMS.
  • DC current: 0–600 A.
  • Jaw opening: ~30 mm (fits most cables in electrical cabinets).
  • Voltage: 0–1000 V AC/DC.
  • Resistance, continuity, diode test.
  • Capacitance (for verifying phase-shift capacitors).
  • Frequency (for verifying mains frequency and variable frequency drive systems).

True-RMS measurement is critical for modern installations with non-linear loads (LED lighting, frequency converters, solar inverters). Standard average-responding clamp meters underestimate current by 10–30% with non-sinusoidal waveforms.

Common Fault Scenarios Diagnosed by the CM275

Overloaded fuse: A 10 A fuse normally carrying 6–8 A suddenly runs hot (>60 °C) — which may indicate that the load has increased to 9–12 A. IGM locates the heat; the clamp meter measures the actual current. Action: reduce load or upgrade the fuse.

Poor connection (loose terminal / high-resistance connection): A loose connection has increased contact resistance → increased power dissipation → localized heat. IGM shows heat at the connection point rather than along the conductor. Action: re-torque the connection with a torque wrench according to the manufacturer’s specifications.

Phase imbalance in a three-phase load: If one phase draws higher current than the others, its neutral contactor becomes hotter. IGM shows the temperature imbalance; three clamp meter measurements confirm it. Action: redistribute single-phase loads to balance the system.

Motor bearing failure: A defective bearing in a motor heats up (across the bearing housing). Motor current often shows a simultaneous increase (the motor works harder against friction). IGM locates the bearing; the clamp meter shows the operating current.

Capacitor bulging in frequency converters: Electrolytic capacitors in VFDs (Variable Frequency Drives) bulge over time due to temperature. IGM detects the overheated capacitors long before they rupture. Action: preventive replacement before catastrophic failure.

NIST-Traceable Calibration

A NIST certificate (National Institute of Standards and Technology) means that BOTH the clamp meter section and the IR section are calibrated against references traceable to international standards:

  • Current: against a calibrated shunt resistor with known resistance.
  • Voltage: against a calibrated voltage reference.
  • IR temperature: against a reference blackbody with known temperature.

Required for:

  • ISO 9001 QMS documentation.
  • Aerospace and military QC.
  • Substation and power plant maintenance documentation.
  • Legally defensible documentation in failure analyses and insurance claims.

Data Logging and Documentation

The CM275 can store:

  • Thermal images (JPEG) with metadata (center-point temperature, timestamp).
  • Numerical measurement values with timestamps.
  • Comments per measurement (via the Bluetooth app).

Data transfer:

  • Bluetooth to the FLIR Tools Mobile app.
  • USB-C to PC for larger volumes of data.

The app can generate automated reports complete with images + measurement values + comments — saving 30–60 minutes of documentation work per service visit.

Applications

Electrical cabinet maintenance: Routine inspection of panelboards, MCC cabinets, and distribution boards.

Motor servicing: Diagnostics of 3-phase motor connections, control circuits, and motor winding integrity.

Solar PV systems: String verification (clamp meter on DC strings) + panel hot spot detection (IR camera).

UPS and backup systems: Battery monitoring with DC current measurement + thermal verification of cells.

HVAC service: Motor operating currents + compressor temperature in heat pump and refrigeration systems.

Retrofit QC: Verification of installations following renovations (current load per circuit + thermal verification after 24 hours of operation).

Education: Vocational schools and technical colleges use the CM275 as a demonstration tool for electrical diagnostics.

Alternatives and Complements

Clamp meter only (without IR): 800–2,500 SEK. No heat detection.

IR camera only: 2,000–10,000 SEK. No current measurement.

Dedicated multimeter + IR camera (two separate tools): Approx. 3,000 + 5,000 = 8,000 SEK. No simultaneous measurement, no unified documentation.

Professional thermography camera (e.g., FLIR E-Series): 25,000–60,000 SEK. Higher resolution (320×240 or more), but no electrical measurement capabilities.

Specifications

  • Clamp meter: 600 A AC/DC True-RMS, 1000 V AC/DC, resistance, continuity, diode, capacitance, frequency.
  • Jaw opening: ~30 mm.
  • Thermal camera: 80×60 pixels, -10 to +150 °C, 150 mK thermal sensitivity.
  • Display: large backlit LCD displaying thermal image and electrical values.
  • Data storage: JPEG images + numerical values, timestamped.
  • Connectivity: Bluetooth + USB-C.
  • NIST-traceable calibration certificate.
  • Rugged design for field use.
  • Battery: rechargeable Li-ion, typically 6–8 hours of continuous operation.

What You Get for the Money

FLIR CM275 AC/DC clamp meter with built-in IGM thermal imaging camera, 600 A True-RMS current measurement, 1000 V AC/DC voltage, resistance/continuity/capacitance/frequency, 80×60 pixel thermal camera with -10 to +150 °C range, simultaneous measurement + thermal image on the display, Bluetooth to the FLIR Tools Mobile app, NIST-traceable calibration certificate, rugged design. 11,356 SEK.

The standard tool for professional electrical technicians in industrial maintenance, commercial facility maintenance, solar PV installation, and power plant service where both electrical measurements AND thermal diagnostics are essential. The premium over a dedicated clamp meter or standalone IR camera is justified by the time saved through simultaneous measurement + unified documentation, plus the safety benefit of IGM allowing remote problem identification before touching any components.

Read more: FLIR CM275 clamp meter + thermal camera in the store →

More news

All news